link motion
英 [lɪŋk ˈməʊʃn]
美 [lɪŋk ˈmoʊʃn]
连杆运动
双语例句
- It cannot allow the link to translate on the horizontal direction, thus enabling the link to do reciprocating motion.
不能让杆子的中心点左右移动，才能做往复运动。 - Then, twists and exponential maps in robotic manipulation are employed to represent the motion of each link, including the general motion of the base link and the rota.
其次在初始位姿估计的基础上，将各个连杆的运动用螺旋和指数映射表示。 - The fit equation of the position and orientation of output link respecting with motion of input link is obtained by using Excel software.
用Excel软件拟合位姿数据，得到每个输入件驱动尺寸与输出件被驱动尺寸位姿拟合曲线和拟合方程。 - It is pointed out that the constraint conditions must be considered in defining end link constraint and analysing the independent motion on end link which is caused by kinematic pairs ih mechanism.
指出应用刚体运动分解原理考察各运动副对末杆产生的独立运动时，必须考虑末杆的约束条件。 - While the dynamics of the fish tail fin is widely studied, the design of the tail fin propeller lacks a kind of simple valid and estimation method, to link the motion parameters of the tail fin with the propulsive force and efficiency.
鱼类尾鳍的动力学问题已经得到广泛研究，但是在进行尾鳍推进器的设计时，还缺乏一种简单有效的设计和估算方法，将尾鳍的运动参数与推力、效率联系起来； - Given two link's lengths of the mechanism, the other two link's lengths which meet the requirement of quick return motion can be easily designed by solving the equations
如果已知机构的任意两杆长度，通过求解该线性方程组，则可很容易地设计满足急回要求的其他两杆长度 - The structure and the work principle of suspending link organization& the work part of small electrically operated fingernail type scarifier in green house is introduced, the kinematic analysis to it is made, its loose earth fingernail motion diagram is simulated.
介绍了小型温室电动爪式松土机的工作部件&摆环机构的构造，工作原理，对其作了运动学分析，并模拟出了其松土爪的运动曲线。 - A study on simulation system of link mechanism motion scheme Based on Solid Edge
基于Solidedge杆机构运动方案仿真系统的研究 - This paper introduces a swing link rack transmission, which evolves from the sliding teeth drive, and its principle as well as the conditions of continuity of motion.
介绍了一种活齿传动的演变体摆杆齿条变程器的原理及其运动连续性条件。 - A Biomechanical Analysis of the Revolving 720 ° Link with Cha in Martial Arts Motion
武术旋子转体720°接跌叉技术动作的运动生物力学分析 - In the paper, the redundancy is used to decrease residual vibration of flexible link robot through optimal self motion, and the method is proved to be efficient by computer simulation.
本文将冗余自由度用于消减柔性杆机器人的残余振动，通过优化选择最优的自身运动以达到减振目的，模拟结果表明，这一方法可以取得很好的效果。 - The effects between the flexible link and rigid one were analyzed based on the dynamic model. The global motion of the rigid link decreases the vibration frequency of flexible link while increases the general damping.
根据模型分析了刚性臂全局运动与柔性臂柔性振动的相互影响，刚性臂的全局运动使柔性臂的振动频率降低，阻尼增加。 - Computer Simulation of Analyzing the Link Motion
连杆机构运动分析的计算机模拟 - The article made optimization design to the maximum transmission angle of fastness cam link combined mechanism which controls manipulator locomotion and better pressure angle of cam in packaging machinery, realized the law of motion of long-term pinpoint stop, compacting conformation, get the well-pleasing impact.
通过对某厂食品包装机中控制机械手运动的固定凸轮连杆组合机构的最佳传动角和凸轮的较好的压力角进行优化设计，实现了精确停歇的运动规律，结构紧凑，取得了满意的效果。 - Chapter III The contrast of the motion link recognition based on motion constraint with the traditional method is made firstly, then expatiation of this method is made.
第三章，将传统的运动链与本研究中运动链做了对比，然后介绍了基于运动副的运动链识别方法。 - Design of wefting insertion mechinism of cam link coupling with two freedoms motion in rapier loom
剑杆织机两自由度的凸轮&连杆组合式引纬机构的设计 - Computer Aided Design for the Link Motion in Warp Knitting Machine
经编机连杆机构计算机辅助设计 - The results show that elastic link device may be invalid under long-period ground motion, furthermore, it may increase the displacement and internal force. So elastic link device not suitable for long-span bridges which build on the site may occur long-period ground motion.
结果表明，弹性连接装置在长周期地震动作用下不仅起不到减震效果，还可能产生反作用，增加结构的位移和内力，不宜应用在可能发生长周期地震动场地上建造的大跨桥梁。 - In the point of the simulation results, the swing link motion law basically accords with the design, which proves the correctness of this method to design the spatial cam profile curve.
从仿真得出的摆杆运动规律图来看，摆杆的运动规律与理论设计基本相符，从而证明了采用此种方法来设计空间凸轮轮廓曲线的正确性。